This set also includes a Complimentary Setup Block (SET-511) for use with 3/4" material to help you set the proper bit height. Both bits feature a high quality bearing for ease of setup while the tongue and groove cuts are approximately 1/16" offset to allow room for expansion. The rounded profile at the bottom of the joint prevents debris on the floor from getting in the way of a nice tight fit.
#Tongue and groove router bits 1 4 professional#
61-511 - Floor Making Router Bit Set with Nail Slotįor working with stock up to 3/4" thick, the tongue cutter on this router bit set features a special nail slot profile for professional results. The tongue and groove cuts are also approximately 1/16" offset to allow room for expansion. The tongue cutter features a 1/2° angle which produces a slight gap at the bottom of the joint to ensure a tight-fitting joint. This matched Flooring Router Bit Set is great for making hardwood flooring with stock up to 1-1/8" thick. 61-509 - Tongue and Groove Flooring Router Bit Set Tongue and groove router bits will cut the 2 mating profiles for this easy to make woodworking joint with ease and with a simple setup. shanks A tongue and groove joint is the ideal way to create flat, even joints for flooring, wainscoting, panels and tabletops.
Features a 1/4" thick tongue and groove joint. The tongue and groove section measures 1/4 in. Both router bits feature bearing guides that will make setting-up and running quick and easy. This type of joint is ideal for custom flooring, wainscot paneling, cabinet backs, and even Shaker-style cabinet doors. Unlike most square profile tongue and groove router bits, our matched V-Tongue & Groove set produces an elegant 45° "V" groove in stock from 5/8" to 7/8" thick. I returned this item but hope they continue to improve their products and would be willing try them again down the road.Choose from three options to fit your needs: 61-504 - V-Tongue and Groove Router Bit Set I also contacted their support and they didn't have an answer for it.
#Tongue and groove router bits 1 4 pdf#
I check the companies website to see if it was available as a pdf but it wasn't. This item also came without any documentation(not even a simple picture showing the dimensions), so later in time when you pull this off the shelf and among other bits, it would be near impossible to know this sets specifications unless you want to break out your dial calipers, or mark the box yourself, or make your own documentation.
And as a result of it's inability to cut anything thicker than 3/4, it is impossible to offset the tongue and grove in any way at all unless you want the extra step of removing the sliver of wood left unremoved. So unless you are going to put typically sold 1inch stock (which could be anything over 3/4) through a planner than you are left with slivers of wood on either side (outsides) of the bit. And the tongue bit is literally sized for 3/4 in thick stock. The result is a sloppy loose fit that, for me, is unacceptable when making cabinet doors and drawer faces. However, I found the groove to be larger than the actual thickness of plywood. I wanted to like this set as it would have been really handy to make groves sized for the actual thickness of plywood.
These bits offered a reasonable cut, based on the very minimal cuts I made (less than 10 total inches). For best results, use with solid wood only. Even though some smaller tongue and groove bits can be utilized in a hand-held router the stability of a table will help keep the joint perfectly square. Tongue and groove bits can take quite a big bite out of the wood, so using these bits in a router table is strongly recommended. This joint also provides a lot of gluing surface as well as aligning ease. A tongue and groove joint is the ideal way to create flat, even joints for flooring, wainscoting, panels and tabletops. plywood to create shaker cabinet door with a plywood center panel. These router bits are designed specifically for use with 1/4 in. plywood is thinner than the stated thickness because of the dressing of the board. This unique tongue and groove Router bit set cuts a slot 5.2 mm thick which is perfect for making tongue and groove doors with a 1/4 in.
0 kommentar(er)
